When using UV curing machine
2019-12-18 15:08:28
Ultraviolet rays can damage the eyes and skin. When turning on the lights, do not use your eyes to look directly at the surface of the lamp, and do not allow ultraviolet rays to shine on the skin.
One, switch machine
1. Turn on the lights sequentially when turning on the lights. Each lamp should be separated by 1 minute. Do not open it at the same time.
2. After the lights are turned off, the fans should continue to operate for a period of time until the lamps cool down.
3, if you want to turn off the lights after the second start, be sure to wait until the lamp is completely cooled before starting, otherwise the lamp surface temperature is not high to start up.
4, can not immediately put into production after the lights, there must be a lamp warm-up time, when the summer temperature is high, the warm-up time is short, when the winter temperature is low, the warm-up time is longer, the warm-up time is about 2-3 minutes, If the UV light machine has a strong or weak light device, the light should be turned on in the strong light stage, which can shorten the lamp warm-up time. If the production requires weak light, it can be adjusted to the low light level after the warm-up is completed.
Second, lamp maintenance
1. The maximum service life of UV is generally 800-1000 hours, and it will be replaced after reaching the end of life.
2. During the use period of UV lamp, use absolute alcohol, gauze plot lamp and reflective board to look for the surface at appropriate time (1-2 months), then rotate the UV lamp 180 degrees, the mirror reflector will lose the mirror effect. After that, it will be even more.
Third, speed adjustment
1, the best speed selection method: the product at a certain speed through the UV curing device, if cured, in speed up until the production through the curing device oh just can not be completely cured, which makes the speed multiplied by 0.8 is the best speed.
2, also pay attention to the use of UV lamp time, with the UV lamp's use of time, energy will be attenuated, the speed will also have to be slowed down.
Fourth, transformers, capacitors
1. The incoming line of the transformer should select when to reach the terminal according to the field activity voltage.
2. After the capacitor is used, it must be discharged if it is repaired to avoid discharging the capacitor.
One, switch machine
1. Turn on the lights sequentially when turning on the lights. Each lamp should be separated by 1 minute. Do not open it at the same time.
2. After the lights are turned off, the fans should continue to operate for a period of time until the lamps cool down.
3, if you want to turn off the lights after the second start, be sure to wait until the lamp is completely cooled before starting, otherwise the lamp surface temperature is not high to start up.
4, can not immediately put into production after the lights, there must be a lamp warm-up time, when the summer temperature is high, the warm-up time is short, when the winter temperature is low, the warm-up time is longer, the warm-up time is about 2-3 minutes, If the UV light machine has a strong or weak light device, the light should be turned on in the strong light stage, which can shorten the lamp warm-up time. If the production requires weak light, it can be adjusted to the low light level after the warm-up is completed.
Second, lamp maintenance
1. The maximum service life of UV is generally 800-1000 hours, and it will be replaced after reaching the end of life.
2. During the use period of UV lamp, use absolute alcohol, gauze plot lamp and reflective board to look for the surface at appropriate time (1-2 months), then rotate the UV lamp 180 degrees, the mirror reflector will lose the mirror effect. After that, it will be even more.
Third, speed adjustment
1, the best speed selection method: the product at a certain speed through the UV curing device, if cured, in speed up until the production through the curing device oh just can not be completely cured, which makes the speed multiplied by 0.8 is the best speed.
2, also pay attention to the use of UV lamp time, with the UV lamp's use of time, energy will be attenuated, the speed will also have to be slowed down.
Fourth, transformers, capacitors
1. The incoming line of the transformer should select when to reach the terminal according to the field activity voltage.
2. After the capacitor is used, it must be discharged if it is repaired to avoid discharging the capacitor.
Self Adhesive Aluminium Foil Paper
Aluminium Foil Paper Price,Foil Paper For Food Packaging,Aluminium Foil Laminated Paper,Self Adhesive Paper Aluminium
Dongguan zuncheng paper plastic material co. LTD , https://www.zcadhesive-label.com