How to replace the blanket quickly and well
2018-06-27 19:01:01
Take the PB1920A, PB1615 offset press as an example:
First, identify the front and back of the rubber splint
In accordance with the position of the three screw holes of the fixed rubber cloth splint in the gap of the rubber roller, distinguish the front (biting side) and rear (dragging side) splints, and mark the top and side of the splice plate to prevent blankets. When the hole is punched, installed before or after or reversed, it affects the quality of punching and installation.
Second, the sizing blanket
1. The warp wire of the blanket must be selected as the direction of tension.
2. When sizing the blanket, we chose a 930mm x 760mm rectangular PS Plate with a very standard cut as the cutting "regular version". The blanket is first laid flat on the workbench with the warp direction perpendicular to the operator, and then the bottom edge of the blanket is used as the reference line, and the desired cut length is measured on the reference line. Then, carefully align the short side (760mm) of the “regular version†with the lower side (baseline) of the blanket along the right cutting point, and use the pen to draw the right trimming line along the right side of the “regular versionâ€; Then shift the “regular version†to the left cropping calibration point of the blanket, draw the left trimming line with a stroke, and finally cut with the knife edge along the trimming edge.
Third, blanket punching
First, the splint with screw holes in the front side (biting side) splint is perpendicular to the end of the blanket in the warp direction, and is set and pressed. Then use a flat head cylinder with ink 50mm long and 5mm diameter, and press the circular imprint on the blanket through the screw hole. Then remove the splint and use the eye punch to punch the circular hole one by one on the blanket. . In the same way, you can punch out the hole on the back (tow) of the blanket.
Fourth, tighten the blanket
It is necessary to fasten one end of the corresponding blanket with a splint with front and rear logos. To ensure the flatness of the blanket when fastening the blanket, tighten it one by one from the center to the other, and use as much force as possible when tightening.
First, identify the front and back of the rubber splint
In accordance with the position of the three screw holes of the fixed rubber cloth splint in the gap of the rubber roller, distinguish the front (biting side) and rear (dragging side) splints, and mark the top and side of the splice plate to prevent blankets. When the hole is punched, installed before or after or reversed, it affects the quality of punching and installation.
Second, the sizing blanket
1. The warp wire of the blanket must be selected as the direction of tension.
2. When sizing the blanket, we chose a 930mm x 760mm rectangular PS Plate with a very standard cut as the cutting "regular version". The blanket is first laid flat on the workbench with the warp direction perpendicular to the operator, and then the bottom edge of the blanket is used as the reference line, and the desired cut length is measured on the reference line. Then, carefully align the short side (760mm) of the “regular version†with the lower side (baseline) of the blanket along the right cutting point, and use the pen to draw the right trimming line along the right side of the “regular versionâ€; Then shift the “regular version†to the left cropping calibration point of the blanket, draw the left trimming line with a stroke, and finally cut with the knife edge along the trimming edge.
Third, blanket punching
First, the splint with screw holes in the front side (biting side) splint is perpendicular to the end of the blanket in the warp direction, and is set and pressed. Then use a flat head cylinder with ink 50mm long and 5mm diameter, and press the circular imprint on the blanket through the screw hole. Then remove the splint and use the eye punch to punch the circular hole one by one on the blanket. . In the same way, you can punch out the hole on the back (tow) of the blanket.
Fourth, tighten the blanket
It is necessary to fasten one end of the corresponding blanket with a splint with front and rear logos. To ensure the flatness of the blanket when fastening the blanket, tighten it one by one from the center to the other, and use as much force as possible when tightening.
Awalong Ceramics Co., Ltd. , http://www.jnceramic.com